I have no clutch it goes to the floor and I cannot find the slave master cylinder for the clutch master cylinder please send pics
I have a 99 Volkswagen Pasan the clutch pedal goes to the floor I'm unable to locate the slave master cylinder or the clutch master cylinder and if you can send pics or illustration or direct me in the right way so I can locate the reservoirs and believe them as I don't believe it is my clutch thank you
My car has a manual transmission.
My car has a manual transmission.
Experienced mechanics share their insights in answering this question :
The reservoir supplying the fluid to both cylinders is the brake master cylinder reservoir. However, adequate fluid there means nothing as a diagnostic. The clutch slave and/or master cylinder could be leaking internally (no visible external leak) or there could be air in the clutch hydraulic system that will have to be bled out. There are other mechanical causes of the clutch pedal going to the floor but in your circumstances that hydraulic circuit should be looked at first. If you desire a diagnostic, and repair of this issue, right at your location, please request a clutch system inspection. If you request that inspection, the responding certified mechanic will get this taken care of for you. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
The clutch pedal sticking to the floor is usually an indication of a hydraulic problem in the clutch system, typically a system that nees bleeding. The clutch hydraulic system does not use engine vacuum. You should also check the adjustment of the overcenter spring above the clutch pedal.
There are typically a few different possibilities for why a clutch pedal will stay on the floor. It could be a failed clutch master cylinder, slave cylinder, failed fluid line, or the clutch has failed.
Remove the linkage from the clutch fork. You may need to remove a bolt with wrenches or a cotter pin with needle nose pliers to remove the linkage or cable. Push on the linkage or cable and see if the pedal will move. If the pedal does not move, then the linkage or cable could be damaged and preventing it from moving.
If it is found under the clutch area of the engine/transmission, it`s the slave cylinder that has worn and failed. Clutch master cylinder failures tend to leak clutch fluid onto the carper above the driver foot pedal area. There will be a bit of an acrid odor in the vehicle if this occurs.
One mistake made, especially by inexperienced drivers, is not pressing the clutch pedal down fully when shifting gears. During this operation, it should be pressed as far as possible to the floor of a car.
When the clutch pedal is released, the springs of the pressure plate push the slave cylinder`s pushrod back, which forces the hydraulic fluid back into the master cylinder.
Common symptoms of a snapped clutch cable:
Clutch pedal sinks freely to the floor – When the clutch cable snaps, there will be no resistance when the pedal is pressed down. This will cause the clutch pedal to sink straight to the floor when pressed.
It is typically an actual pedal located to the left of the clutch. The dead pedal allows for the racer or driver to keep the left foot on the same plane as the clutch, thus making the transition between them smoother and faster. However, the dead pedal still serves no function to the car itself.
The classic symptom of a failing master cylinder is a brake pedal that “dives” or sinks slowly to the floor while pedal pressure is being applied. Another sign to look out for is any leaks around the master cylinder. If a seal is worn out, it may leak past the seal and onto the pushrod that attaches to the brake pedal.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have no clutch it goes to the floor and I cannot find the slave master cylinder for the clutch master cylinder please send pics
ANSWER : The reservoir supplying the fluid to both cylinders is the brake master cylinder reservoir. However, adequate fluid there means nothing as a diagnostic. The clutch slave and/or master cylinder could be leaking internally (no visible external leak) or there could be air in the clutch hydraulic system that will have to be bled out. There are other mechanical causes of the clutch pedal going to the floor but in your circumstances that hydraulic circuit should be looked at first. If you desire a diagnostic, and repair of this issue, right at your location, please request a clutch system inspection. If you request that inspection, the responding certified mechanic will get this taken care of for you. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.
Clutch pedal goes to the floor and doesn’t return
ANSWER : Hello, thanks for your question. You could watch the clutch fluid as it mentions in the test, but this really doesn’t tell you much. Most of the time this is caused by a bad clutch master cylinder. If the fluid level is low the first thing to do would be to locate the leak. If the fluid is full then I watch to see that he clutch slave is moving when the clutch is pressed. If it is and if it is releasing but the pedal stays down then that is another reason to change the clutch master. If the clutch slave and fork are not releasing then it may have an internal clutch failure. If you would like help getting this inspected or repaired, consider YourMechanic, as a certified mechanic can come to your home or office to perform the inspection and make or suggest any repairs needed.
Clutch pedal stays to floor. Replaced master cylinder. Clutch push rod broke. Also do I need to change slave cylinder
ANSWER : If you have an issue with your clutch pedal going to the floor, the slave cylinder is normally the cause of this circumstance.
Also, if the push rod has been broken the first step would be to track down a new one because that push rod is a very necessary part of the clutch pedal system.
Once a new push rod has been located and installed, I would recommend having a new slave cylinder installed as well.
If you are in doubt about this repair, I would recommend having it performed by a qualified professional, such as one from YourMechanic. One of our mobile technicians will be able to come to your home to diagnose the issue with your clutch pedal and replace your clutch slave cylinder as necessary.
Clutch not working after replacing slave cylinder and master cylinder
ANSWER : Hello. We will be happy to help you with your vehicle. It sounds like you have a problem with your throw out bearing. You would likely need to drop the transmission once again and check that the installation of the throwout bearing is proper. You may also try to peel back the boot around the slave cylinder to see inside of the transmission. By doing so you may be able to see possible damages on the throwout bearing. It will be a great idea to use a stethoscope before you take the vehicle back apart to help pinpoint exactly what portion of the transmission coming from. Another very important thing that you should check are your axle’s, make sure they are seated correctly inside of the transmission.
Replaced clutch master and slave cylinder, but my car still won’t go into gear while running
ANSWER : If the hydraulics are working correctly, there are a couple of things that could be wrong with the clutch that would prevent it from releasing. Unfortunately, any of them will require removal of the transmission for repair.
At 191,000 miles, it could be that your pressure plate has failed and is not fully releasing, or it could be that the disk is severely worn and there is an accumulation of debris between the disk and the plate which would also keep it from releasing. Either of these would be corrected with a clutch replacement.
If you contact YourMechanic, they can send a technician to your home to evaluate your problem and help you figure out what to do next in order to avoid any unnecessary repairs.
My clutch is not working Entire clutch repair or clutch master cylinder repair? How do I check the cylinder?
ANSWER : Hi there. Check the slave cylinder to the clutch and see if the piston is all the way out. If the piston is all the way out or its not touching the clutch fork, then the release bearing has broken and the fork has moved into the clutch. If the slave cylinder is relaxed and the fork is against it, then the clutch pressure plate has sprung a pressure spring. If the pedal can go down but not all the way to the floor, then the clutch needs replaced with a new release bearing. If you need further assistance with a clutch replacement, then seek out a professional, such as one from Your Mechanic, to help you.
Master cylinder and clutch slave cylinder replaced
ANSWER : Unfortunately, using the same plastic clutch slave cylinder assembly the vehicle was manufactured with will cause the same results if the vehicle is abused. The plastic part is very strong, but cannot withstand the heat and pressure from hard driving. You may be able to do some research and find a higher performance part produced by an aftermarket company, as some companies specialize in manufacturing upgraded parts for higher performance. If you would like some assistance with this, one of the technicians from YourMechanic can come to your location to inspect the shaking problem and let you know what repairs are needed.
Clutch pedal goes to floor when pressed
ANSWER : With the symptoms you have described, the most likely cause is a leak in the clutch hydraulic system. If there is a leak on the system it causes air to enter. Since air is not able to be compressed the clutch pedal remains stuck to the floor when it is pressed down. With everything going on with this car, it is unsafe to be driven until the clutch has been repaired. A qualified technician, like one from YourMechanic, will be able to confirm the cause of your clutch issue and perform the needed repairs to get you back on the road.
