I have a 2010 camry. I just recently replaced the engine with a 2014 camry engine. Now I have Four engine lights on. I replaced on
I have a 2010 camry. I just recently replaced the engine with a 2014 camry engine. Now I have Four engine lights on. I replaced onE sensor n I need to replace the engine mounts. Could that be the issue?
Experienced mechanics share their insights in answering this question :
If you swapped the engine from a vehicle that is 4 years newer than the car is then you are going to have electrical and sensor incompatibilities that may not be able to be fixed by just a few sensor replacements. There were many changes in computer and emission related items between 2010 and 2014 engines. I would recommend having a mechanic like one from YourMechanic come to you and compare the two engines to isolate the possible differences and see if the problem can be fixed.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
2014 Toyota Camry Check Engine Light Flashing
Diverse common reasons for a Check Engine Light are damaged oxygen sensor, faulty emissions control part, dirty mass airflow sensor, faulty head gasket, a malfunction with the fuel injection system, or defective spark plugs to name a few.
Turn off the car while holding the trip meter reset. Turn the Camry on to accessory mode with the button still held down. The illuminated odometer reading will disappear and then reappear; during this time, release the button, and the engine light will go out.
2012 Toyota Camry Check Engine Light Flashing
Other common reasons for a Check Engine Light are dirty mass airflow sensor, faulty emissions control part, a malfunction with the fuel injection system, damaged oxygen sensor, faulty head gasket, or defective spark plugs to name a few.
Toyota Camry Check Engine Light Flashing
Other common reasons for a Check Engine Light are dirty mass airflow sensor, a malfunction with the fuel injection system, faulty emissions control part, faulty head gasket, damaged oxygen sensor, or defective spark plugs to name a few.
2014 Toyota CAMRY (2.5L 4 -cyl Engine Code 2AR-FE B)
In most cases, successfully repairing the issue that caused your light to come on will cause the check engine light to turn off automatically—but only after 10 to 20 “cycles”. A cycle, in this instance, refers to the process of turning the vehicle on, running it for some time, and turning it off again.
Quickly, push and hold the odometer button your dashboard, then turn your key to position two. Continue to hold the odometer button for 10 seconds.
This is a sign you should stop driving and have your car looked at by a mechanic as soon as possible. Use your best judgment on whether to call a tow truck or drive yourself to a nearby repair shop. Is the light flashing? In many vehicles, there are two types of check engine lights—a solid light and a flashing light.
These problems can range from faults within the electrical system, the engine, fluid levels or to problems within the car`s emissions system. The problem can even be as simple as forgetting to tighten your gas cap – in fact, this is the most common reason why check engine lights appear in the first place.
The check engine light, or malfunction indicator light, usually means that your car is experiencing an engine problem. But it can come on for many other reasons, ranging from a simple loose gas cap to a more serious bad catalytic converter. Furthermore, what triggers the light varies by year, make, and car model.
2022 Toyota Camry Check Engine Light Flashing
Other mainly common reasons for a Check Engine Light are damaged oxygen sensor, damaged emissions control part, damaged head gasket, a malfunction with the fuel injection system, dirty mass airflow sensor, or defective spark plugs to name a few.
2010 Toyota CAMRY (2.5L 4 -cyl Engine Code 2AR-FE B)
A: The VIN digit and the engine code are two separate things. OEMs use the VIN engine digit to specify the type of engine, and they use the engine code to signify a change to that engine.
If you want to perform a full reset, wait at least 15 minutes before reconnecting the battery to ensure all residual power has been drained. A full reset reverts your ECU to its factory settings and likely causes it to forget its learned ideal shift points and air-fuel mixing ratios.
To make sure the check engine light does not reappear, it`s recommended that you drive your car 30 to 100 miles. This enables the vehicle`s “Drive Cycle” to reset, as the various sensors need time to recalibrate.
A loose gas cap is one of the most common reasons for the check engine light to go on. Check that your gas cap is screwed on securely and that it`s in good condition. If you have a tank of bad gas in the car, your check engine light may come on.
This is a sign you should stop driving and have your car looked at by a mechanic as soon as possible. Use your best judgment on whether to call a tow truck or drive yourself to a nearby repair shop. Is the light flashing? In many vehicles, there are two types of check engine lights—a solid light and a flashing light.
This is a sign you should stop driving and have your car looked at by a mechanic as soon as possible. Use your best judgment on whether to call a tow truck or drive yourself to a nearby repair shop. Is the light flashing? In many vehicles, there are two types of check engine lights—a solid light and a flashing light.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a 2010 camry. I just recently replaced the engine with a 2014 camry engine. Now I have Four engine lights on. I replaced on
ANSWER : If you swapped the engine from a vehicle that is 4 years newer than the car is then you are going to have electrical and sensor incompatibilities that may not be able to be fixed by just a few sensor replacements. There were many changes in computer and emission related items between 2010 and 2014 engines. I would recommend having a mechanic like one from YourMechanic come to you and compare the two engines to isolate the possible differences and see if the problem can be fixed.
Check engine light refuses to go off after engine replaced
ANSWER : Hello there, you have a long series of issues going on with your 2013 Hyundai Sonata. If you keep getting a repeating oil light on than there is likely a fault in that system.
Since this fault has lasted after the engine was replaced it could be a oil pressure sensor, wiring harness fault, ECU fault, oil pump, oil strainer clogged, or low oil pressure.
To diagnose this issue properly you need a complete vehicle inspection to start from square one and identify the root cause of all this.
Abs light, emergency brake light, steering wheel assist light, engine light, EPC light, traction control light
ANSWER : Hello, thank you for writing in. The vehicle does utilize a lot of the same sensors for these systems. Are there any other codes that are coming up when this code appears? If so you will want to take these into consideration when processing the repair and making a diagnosis. The module may be bad, and replacing it should fix the problem. The lights should turn off once the main computer recognizes the new module and the sensors sync up. If you believe the sensors need to be cleaned you may do so. Do as minimal as possible to make sure you are not damaging the sensor or disrupting the wiring inside. A bad connection would make the lights stay on. With so many lights that are effected by the module being illuminated, the module is likely bad or does not have a connection. Check the connection first and then resort to replacing the unit. For more help with these electrical tests, contact our service department.
I have a 96 Ford ranger with cel p0340 I have recently done a timing belt, engine runs great replaced cmp sensor cel still on
ANSWER : Hi There,
This may happen for a couple of reasons. First, check to be sure that the connections to the sensor are clean and not faulty or broken. Secondly, check to be sure you replaced the correct sensor as there are two camshaft position sensors in some applications. If you need further help with this, please reach out to us here at YourMechanic as we are always here to help.
This may happen for a couple of reasons. First, check to be sure that the connections to the sensor are clean and not faulty or broken. Secondly, check to be sure you replaced the correct sensor as there are two camshaft position sensors in some applications. If you need further help with this, please reach out to us here at YourMechanic as we are always here to help.
in my car battery warning light appearing while driving.so I have replaced both battery and alternater still light is on
ANSWER : As you may yourself have seen, there are many reports of this fault with the Civic, that is a battery or alternator is replaced only to have the warning light fail to extinguish despite checking every conceivable electrical possibility. Your only recourse is to have a certified mechanic go through that exercise with your car and that involves first attempting to "re-set" the light. If the warning light returns, the alternator output has to be carefully measured both loaded and unloaded. All terminal connections have to be verified including all grounds. Fuses have to be checked for integrity (continuity) and the possibility of shorts, in for example dash wiring, has to be checked. To request this repair, simply request an electrical components diagnostic and the responding certified mechanic will seek a resolution to this.
2012 equinox reduced power light engine light and traction light came on. Lost a lot of power got home and all light except engine
ANSWER : Your car has what is called a "safe mode" that will be engaged by the computer when it detects that something critical has gone wrong related to any of the major components in your engine chassis or power train. This may be related to a number of things, most of which should have been registered in the computer when the check engine light came on. I recommend having an expert from YourMechanic come to your location to inspect your check engine light and diagnose any codes registered by your vehicle’s computer.
Engine Light and AT light. Car goes into limp mode
ANSWER : Hello. Most of the time this is the result of a transmission failure. It is common for this transmission to have internal pressure problem which will cause these codes. It can also be a voltage problem so I always check that first. I check the voltage going to the transmission and if it is too low I repair that issue which is commonly the ignition switch. If the voltage is fine, then the transmission pressures need to be checked and it will more than likely need to be replaced. I would have a transmission specialist look into this.
My Hyudai elantra 2014 stalled and stopped after the battery light, engine light and oil light came on
ANSWER : Hello, thank you for writing in. With check engine lights on, the first step is always scanning the vehicle for codes. These help direct your attention and ease diagnostics. The main concern is that the engine is making a loud noise. We need to determine if the noise and the battery or oil light are related. A major issue with the engine would effect the alternator charging the battery, the oil pressure, and several other components. However issues with the drive belt and other components can play a factor as well. Electrical and charging issues can cause various sensors to fail, and cause other warning lights to turn on. Only further inspection will tell, and you may need to get a second opinion. For help from our technicians, contact our service department to schedule an appointment.
