Fuel pump not pumping gas. 1996 Chevrolet Blazer

ANSWER : Hey there, thanks for writing in about your 1996 Chevrolet Blazer. If you hear the pump, but still get no fuel out of the pump, then you have the power and ground backwards in the wiring or they have it backwards on the pump. If you need help having this checked, a certified professional from YourMechanic can inspect the starting issue and let you know what repairs are necessary.

ANSWER : You need to look at the theft light on dash to make sure it comes on and goes off when you turn the key to the on position. If light comes on and stays on then your theft system is causing the fuel pump to not be engaged. I recommend you check the theft system and then scan the computer for theft system codes. You may need to reprogram the keys to work or you have an bad sensor for the ignition key in the steering column.

ANSWER : Hi there – the metal component you describe is a fuel check valve on the fuel return line. Its function is to maintain a small amount of pressure in the fuel system so that starting does not require the fuel pump to run very long before the engine will start. Having replaced the fuel pump and fuel filter, I would check fuel pressure while the car is running. This is to check the fuel pump relay for burned contacts that won’t support full electrical current to the pump, and for proper fuel pressure – a malfunctioning fuel pressure regulator could also restrict power and higher speeds if pressure is too low. I would recommend an inspection of the fuel system by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : Hi There,
It sounds like you may have a clogged fuel injector or potentially a faulty injector that is fried internally. I would suggest testing them if you have access to a multi meter. Disconnect the injector from the electrical connector and set your multi meter to Ohms mode and measure the resistance of the injector. After testing all injectors, compare the resistance. They should be the same or very close. If they are not, they will likely need to be replaced.

ANSWER : Hi there – I suspect you have weak power getting to the fuel pump. I would first check the voltage coming out of the fuel pump relay. If the contacts in the relay are burned, you will not get reliable current flow to the pump. Check the fuel pump ground as well (voltage drop across the ground, not just continuity). I recommend a fuel system inspection performed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : Hi there. There could be multiple issues causing your lack of spark problem, ranging from a minor electrical short in the main relay to an issue with your ECU. In order to know for sure, you should have a professional mobile mechanic complete an electrical problems inspection.

ANSWER : The switch you are referring to is vended with the required electrical and fuel schematic (I just looked in the box) that answers your installation question. If you want an advance view, here is a link as well. Yes, you need a return line and just refer to the aforementioned link. If you are retrofitting back to OEM, I strongly encourage you to buy the original Factory Service Manual (FSM). There are lots of details attending this system and obviously it is difficult to recount it all here. The FSM will make your life much easier and you can then make sure your installation is perfect. Alternatively, YourMechanic can dispatch a certified mechanic and perform the whole retrofit and check out if you desire. Just request and schedule a generic service such as fuel pump service and the mechanic will come to your location and estimate the parts and labor required. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Hello, thank you for writing in. The fuel pump likely has been shorted out due to the moisture. At this point you will need to replace the fuel pump, and possibly the fuel pump fuse/relay. With that being said, you can do some further electrical testing on the system to see how much damage was done. A surge in the system can cause failure across the circuit, however it usually stops at the fuse or relay. This is one of the safety features that the fuse is designed to help with. With a fuse to blow, more electrical components may be effected by the surge. The required testing can all be done at home with a voltmeter if equipped. If not equipped, you will want to seek professional assistance. Contact our service department if you find yourself in need of help.