Everytime I put car into gear it shuts off the car but idles fine

ANSWER : Hi there. The clutch may be worn and slipping causing the engine to stay running as the shifter is put into a gear selection. If the clutch was working, when put into gear and let off the clutch pedal, the vehicle will either move or stall out the engine. Check the slave cylinder and see if the return spring has broken off causing the clutch fork to stay engaged. Also the clutch adjuster cable could be out of adjustment or damaged. If the pedal and hydraulic assembly has no issues, then I recommend seeking out a professional, such as one from Your Mechanic, to help you diagnose your clutch.

ANSWER : This sounds like a faulty speed sensor problem. Most cars have two speed sensors (one monitors input shaft and one monitors output shaft) which tell the computer what the gear ratio is of the transmission while in use. If either of these are not working properly, they will cause the computer to shut the car off for safety reasons. I would suggest having an expert from YourMechanic come to your home to diagnose your stalling issuee and help you repair it.

ANSWER : Hi there. What had happened is the wrong key set the security to the vehicle. This is to prevent the vehicle from starting with the wrong keys. Try removing the battery cables (+) and (-) for 13 minutes. During that time, put the original key in the ignition and turn it on. Activate everything in the car even though there is no power. Then remove the key and hook up the battery cables. The computer should have reset and reset the security. If the security is still being tripped, then I recommend seeking out a professional, such as one from Your Mechanic, to help you

ANSWER : Hi there – Your symptoms describe the behavior to expect when your clutch hydraulics go out (clutch master and clutch slave cylinders). Check your clutch fluid level – it may be low. If the fluid level is low, this usually means your clutch slave cylinder has worn out, not unusual with your mileage, and should be replaced. I recommend a malfunctioning clutch inspection performed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : If the clutch mechanism is releasing properly, and the shift linkage is not malfunctioning, your transmission will have to be removed from the vehicle and inspected. Once a transmission has been removed from a vehicle, if the problem is a broken or worn part or parts, and the transmission has 100,000 miles or more, the most cost effective approach is to just simply rebuild the whole transmission. There are transmission rebuild kits that are sold just for this purpose. Rebuilding a transmission is no big deal and is indeed easier in many respects than rebuilding an engine. You can rebuild your transmission right in your own garage. You can NOT rebuild an engine in your own garage due to the highly specialized, and extremely costly, machine shop equipment required. Occasionally, mobile mechanics will take on a transmission rebuild job especially as once the mechanic removes the transmission from the vehicle, it is just simply a modular unit that can be easily transported to a mechanic’s shop and rebuilt right there and then returned to your vehicle. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Hi there:

There could be multiple problems on your Saturn that are causing this problem you’re experiencing. If your clutch is worn it won’t allow you to put your car in gear. When you step on the clutch, the transmission disengages from the engine. This slows the insides of the transmission just enough to allow you to shift gears. When the clutch is worn, the slave cylinder doesn’t have enough travel to disengage the clutch from the engine, so it wont allow you to put it in gear. It’s also possible that you have broken a shift fork in the transmission. The shift forks are what actually move the slides inside the gear box to engage the gears when you move the shifter. The best way to determine exactly why you’re car won’t shift into gear is have a professional mobile mechanic complete a car is hard to shift inspection.

ANSWER : The transaxle is not engaging internally to the axle shafts inside the transaxle or you have one or both axle shafts disengaged from the transaxle. The fact that the speedometer moves when gear is engaged and clutch is released shows the speed sensor in the transaxle is getting turned.

You will need to have the vehicle raised and the axles inspected for broke or stripped shafts. If the axles do not have anything visually wrong with them then hold one wheel and try to turn the other wheel while transaxle is in gear, with engine off, to see if the wheels are locked together. When you spin one wheel the other wheel should turn in the opposite direction. If it does not then the problem is in the transaxle differential gears and the transaxle would need to be removed and disassembled to find the broken internal components.

If you need some assistance with this, consider YourMechanic, as one of our mobile technicians can come to your home or office to diagnose your acceleration issue and help make the necessary repairs to get you going again.

ANSWER : If the clutch lever, on the transmission, is functioning something has mechanically failed in the clutch and/or the transmission. If the clutch failed, and you heard gears grinding, as you tried to shift the transmission, some damage may have been done to the transmission. Even if just the clutch has failed, the engine and transmission will have to be separated to find the cause of the failure and worn out or broken parts will likely have to be replaced . To request an inspection, the recommended service is clutch system diagnostic. If you request that diagnostic, the responding certified mechanic will evaluate what you have and let you know of your repair options and costs. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.