Car wont start–check engine, oil pressure, and battery light all on

ANSWER : The fuel pump will not stay on if you loose oil pressure. This is why it is shutting off. The loss of oil pressure may be from bad crankshaft bearings or camshaft bearings. The engine oil pan should be removed and the oil pump needs to be checked to ensure that you put in the pick up tube seal to the pump and connected the pump to the block. Then remove at least one main bearing cap and inspect the bearings for excessive wear and crankshaft damage. If you need some help with this, consider YourMechanic, as a certified technician can help diagnose the issue with your oil pressure firsthand and help you fix it accordingly.

ANSWER : Hello there, you have a long series of issues going on with your 2013 Hyundai Sonata. If you keep getting a repeating oil light on than there is likely a fault in that system.

Since this fault has lasted after the engine was replaced it could be a oil pressure sensor, wiring harness fault, ECU fault, oil pump, oil strainer clogged, or low oil pressure.

To diagnose this issue properly you need a complete vehicle inspection to start from square one and identify the root cause of all this.

ANSWER : Hi There,
If your oil pressure falls below a specific level, the ECM (car’s computer) will automatically shut the engine down to avoid further damage to the engine. This is done as a safety precaution. Typically, the oil pressure light will come on when you are in fact low on oil, the oil pump is not pumping oil properly or in some cases when the oil pressure sensor is faulty providing a false reading. In any case, this should be looked at as soon as possible by a qualified mechanic. I would suggest having one of our experts here at YourMechanic come to your location to take a look at your vehicle.

ANSWER : It is possible that they put in the wrong viscosity oil. In rare instances, a defective filter will also cause low pressure. If there is too much oil, it will aerate and cause low pressure. Be sure the oil level is really not above "max". The P2187 code will appear if the oil fill cap is not tight but it will also appear due to a myriad of causes because that code only "generally" identifies a lean running condition. Consequently, numerous parts would have to be tested including the O2 sensor, gas cap seal, manifold air leaks, any vacuum leak anywhere including PCV and EVAP systems, exhaust leaks, and fuel system faults such as failing fuel pump, clogged filter and more. Since the car has relatively low mileage, you would not expect a failed oil pump, although the pressure sensor (or switch) could be bad. However, the occurrence of the oil pressure warning light is quite coincidental to the oil change, thus I would suggest bringing the car back and asking them to redo with a new filter and double check the viscosity of the new oil that they use. If the problem persists after that, you will have to test actual operating oil pressure (at idle for instance) as well as the oil pressure switch. Finally, if the oil pressure warning light comes on continuously, unless the warning circuit itself is malfunctioning, that means the oil pressure is too low to operate the engine without damaging it. Anytime the light comes on for more than literally an instant, you should shut down the car and thus an issue like this obviously has to be repaired.

If you’d like, a YourMechanic certified mechanic can come to your home or place of business to inspect the vehicle and perform an oil pressure light is on inspection to diagnose the vehicle and suggest potential repairs.

ANSWER : Hi and thanks for contacting Your Mechanic. If sometimes your vehicle will start with the new alternator and sometimes it won’t, then there is a loose connection in your charging system. Check all of the wires to the alternator and to the battery. Make sure that the battery cables are clean and tight. Make sure that the wires to the starter are clean and tight. A loose ground to the ignition system will cause the vehicle to not crank over. Check all of the ground wires from the battery to the starter. Make sure that they are clean and tight. If you need further assistance troubleshooting your no start situation, then seek out a technician, such as one from Your Mechanic, that can assist you.

ANSWER : Hi there. It is possible that the battery cable came loose or the wires to the oil pressure sensor has came loose or failed. Check the battery cables and make sure that the terminals are tight and clean. Check the wires to the oil pressure sensor and make sure that they are connected and not broken. If everything looks good, then the oil pressure sensor may have failed. Plus, check the computer for codes and see what is stored. This will lead you to the part that could have failed. I recommend replacing the oil pressure sensor then checking to see if the lights will go out. If you need further assistance troubleshooting your vehicle, then seek out a technician, such as one from Your Mechanic, that can assist you with the warning lights that came on.

ANSWER : As you may yourself have seen, there are many reports of this fault with the Civic, that is a battery or alternator is replaced only to have the warning light fail to extinguish despite checking every conceivable electrical possibility. Your only recourse is to have a certified mechanic go through that exercise with your car and that involves first attempting to "re-set" the light. If the warning light returns, the alternator output has to be carefully measured both loaded and unloaded. All terminal connections have to be verified including all grounds. Fuses have to be checked for integrity (continuity) and the possibility of shorts, in for example dash wiring, has to be checked. To request this repair, simply request an electrical components diagnostic and the responding certified mechanic will seek a resolution to this.

ANSWER : Hi there. Check the engine oil level. If the oil level is low, then top off and recheck the symptoms. If the engine oil is full and the oil pressure light is lit up on the dash, then either the oil pressure sensor has failed or the oil pump has failed. Take a look at the oil pressure sensor and see if the contacts are loose or damaged. If the oil pressure sensor seems to be intact, then I recommend removing the sensor and putting in a test gauge and checking the oil pressure as the engine is cranked. If there is oil pressure of 25 psi or greater, then the oil pressure sensor needs replaced. If there is no oil pressure, then the oil pump needs replaced. If you need further assistance with your warning lights being on for the engine oil, then seek out a professional, such as one from Your Mechanic, to help you.