brake and abs light won’t go off after replaceing brake pads and ft. rotors.
2 weeks ago I replaced left and right front rotors and pads, also replaced hub on right side only. Rear brakes were good. The problem I am having is how do I stop the Brake and ABS light from still coming.
on?
You drive about 3 blocks and off goes the warning sound and the Brake and ABS lights go on. I don,t see any reason why those warning's are still going off. Please help.
on?
You drive about 3 blocks and off goes the warning sound and the Brake and ABS lights go on. I don,t see any reason why those warning's are still going off. Please help.
Thank you Bill Wolf
My car has 120000 miles.
My car has an automatic transmission.
Experienced mechanics share their insights in answering this question :
Your car is equipped with wheel speed sensors at each of the four wheels which monitor wheel speed while relaying this information constantly to the ABS and traction control system which are controlled by the car’s ECU. When the ECU senses an abnormal speed given specific conditions, it engages the ABS or traction control as needed to control the vehicle properly and safely. In your case these sensors may have been bumped or need to be reset due to the movement when the brakes were replaced. I would suggest having a professional from YourMechanic come to your home to diagnose your ABS and traction control system.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
If both the ABS and the brake system light come on at the same time, your vehicle is no longer safe to drive. This means there is a serious problem with the car`s braking system and continuing to drive puts yourself and others at risk.
Buick LaCrosse Anti-lock Brake System (ABS) Diagnosis Cost.
The most common ABS problems occur when sensors become contaminated with debris or metal shavings. Malfunctions also occur when sensor wiring becomes damaged, resulting in intermittent or no continuity.
If the light really is the ABS light, the first thing to try is turning the ignition key off and back on. It`s like rebooting your computer. Maybe whatever transient issue that confused the ABS controller has passed and all is well. If the condition repeats, you need to do some further poking and prodding.
Blown Fuse or Stuck Bulb
Sometimes a blown fuse to the ABS can cause the light to come on and stay on. Fuses are easy to blow, so sometimes it`s an easy fix to check.
ABS is malfunctioning: Traction control and ABS (anti-lock braking system) often share the same control module and internal self-diagnostics system. As a result, sometimes an issue in the ABS can trigger the traction control light. If this is the case, then both the ABS and Traction Control lights will be on.
On a passive ABS sensor, measuring resistance across the signal and ground leads generally produces a reading of 800-2000 ohms. A steady reading within this range indicates a good sensor. If the resistance is constantly changing or increasing on the meter, the sensor is faulty.
An ABS sensor is a wheel speed sensor that helps your car`s ABS system know when to engage. The ABS system is designed to kick in during emergency braking situations to help prevent your wheels from locking up. This, in turn, helps you maintain control of your vehicle and avoid accidents.
1. ABS Light is illuminated on the dashboard. Since the wheel speed sensor also monitors the anti-lock braking system on your car, it`s common for the ABS Light to illuminate when the sensor is worn out, disconnected, or has been struck by debris, which means you`ll have to replace the wheel speed sensor.
The anti-lock function will stop working properly, which may increase the distance it takes to safely stop your vehicle. The rear tires will lock, which will increase vehicle swing on turns and may make your vehicle more difficult to control.
If the ABS system is not functioning properly, then your vehicle is likely to skid, hydroplane and lose traction under heavy braking conditions. The last time you want to find this out is when you need it most in tough conditions, which could lead to an accident on the road.
Signs of a failed ABS system include ABS light always ON, on your dash, the car not braking correctly (brake pedal feels different to normal), or loss of control while braking. Reduced braking performance – A failing ABS relay can cause reduced braking performance, especially during hard braking.
Resetting Your ABS Dashboard Warning Light
Step One: Disconnect the positive cable from your car battery. Then, hold down the brake pedal to drain the vehicle`s electrical system. This will result in a reset of the car`s central computer. Plug the cable back in to restore power.
If your ABS light comes on individually, you are safe to drive your car to your destination, as your normal brakes will still work. You will, of course, have to be more careful as your ABS will not respond in case of an emergency.
One reason your vehicle`s ABS light is on is because it may be sensing abnormally low levels of brake fluid. You`ll be able to notice if your brake fluid is low by the way your car brakes. The braking may seem soft or spongy. However, if the brake fluid is low, you`ll probably see more than just the ABS light come one.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
brake and abs light won’t go off after replaceing brake pads and ft. rotors.
ANSWER : Your car is equipped with wheel speed sensors at each of the four wheels which monitor wheel speed while relaying this information constantly to the ABS and traction control system which are controlled by the car’s ECU. When the ECU senses an abnormal speed given specific conditions, it engages the ABS or traction control as needed to control the vehicle properly and safely. In your case these sensors may have been bumped or need to be reset due to the movement when the brakes were replaced. I would suggest having a professional from YourMechanic come to your home to diagnose your ABS and traction control system.
Abs light, emergency brake light, steering wheel assist light, engine light, EPC light, traction control light
ANSWER : Hello, thank you for writing in. The vehicle does utilize a lot of the same sensors for these systems. Are there any other codes that are coming up when this code appears? If so you will want to take these into consideration when processing the repair and making a diagnosis. The module may be bad, and replacing it should fix the problem. The lights should turn off once the main computer recognizes the new module and the sensors sync up. If you believe the sensors need to be cleaned you may do so. Do as minimal as possible to make sure you are not damaging the sensor or disrupting the wiring inside. A bad connection would make the lights stay on. With so many lights that are effected by the module being illuminated, the module is likely bad or does not have a connection. Check the connection first and then resort to replacing the unit. For more help with these electrical tests, contact our service department.
EPC light on 2004 Jetta. Code said brake switch faulty, but brakes lights worked. Replaced brake switch, now no brake lights.
ANSWER : Hi there. The first thing that pops in my mind beyond of what you have listed is perhaps the electrical harness attached to the brake switch. Perhaps the harness itself is damaged or you have an exposed wire, loose ground wire somewhere. You might want to have a professional mobile mechanic come to your location and complete a brake lights not working inspection to help you diagnose this issue.
abs light on brake line broke have been replace I bleed brake line but brake pad still go to the floor now wheels lock up
ANSWER : Hello. If the brake pedal is going to the floor then that means that it is not building pressure. If the brake system has been fully bled and there is no air in it then most of the time it is a bad master cylinder or it can be caused by a bad ABS module. If the brake fluid was low and if air got into the system then the only way to properly bleed it is with a scan tool that would allow you to open and close the valves in the ABS unit. Air gets trapped in these easily if the brake fluid gets low. This can also explain why the brakes are locking up. I would usually use my scan tool to bleed the system out first before going any further. I would also scan the brake control module to see what it is reading as a fault. If there is no air in the system and if there is no prominent code then I would replace the master cylinder first. If you want to check out why your brakes are locking up, consider YourMechanic, as a certified mechanic can come to your home or office to diagnose and repair this.
Brake lights are not working. replaced brake light swtch still no brake lights. the third brake light the connection was melted at
ANSWER : The first thing to do is to repair third brake light and replace the brake light fuse and then see if the third brake lights work and the lower lights start working? If only the 3rd brake light starts working then you may need a further checks on the turn signal flasher or switch could be bad.
Brake light and abs light on, my brakes are soft ( needs to be replaced ) if I replace brakes will both lights go off?
ANSWER : A soft brake pedal generally indicates a hydraulic issue with the brake system. If the hydraulic system has a leak or a faulty seal in components such as the brake master cylinder of ABS pump, the brake system will not operate with the correct pressure. Worn brake pads may make the brake pedal travel farther than say new brake pads, but this generally does not cause a "soft" brake pedal. Replacing brake pads may not turn the ABS and BRAKE lights off. An abs system inspection should be performed by a certified technician before replacing any parts that may or may not correct your issue. I cannot predict if you will have a further issue but as far as is it unsafe ? Yes, driving with a possible hydraulic fault with the brake system is very unsafe as the brakes may fail entirely.
When I put my foot on the brake my back left brake light goes off, when I take it off the brake the brake light comes on
ANSWER : I would suggest trying to disconnect and reconnect the wiring to the rear lights. I have seen these older Toyota vehicles rear lighting short out on the lights themselves due to the way the light circuit was made on the lamp housing. Look at the housing circuit on the light to see if one is touching another, and that could tell you why it is malfunctioning. There could also be a problem with the brake light switch. If you are not comfortable dealing with wires, I recommend getting in touch with a certified mechanic who can look at your brake light issue for you to see what’s going on.
I replaced the brake light switch. Gear lever unlocked because it had locked. Now the brakes feel hard.
ANSWER : Hi, thanks for writing in. You need to check the brake switch install adjustment. You may have the switch adjusted too tight and it is holding the the brake pedal partly down. This will cause the brake master cylinder to not release the brakes when you let off the pedal. Readjust the switch away from the pedal until you feel some free play again in the pedal. This should fix the problem. If you would like help, consider having an expert automotive technician from YourMechanic come to your home or office to inspect and diagnose this issue for you, and make or suggest any repairs as needed.
