Brake hose instructions states that hose must be straightened and left in warm area before installation. How important is this.
The hose replacement is on a 73 Dodge Challenger and is about 14". It runs from the under body to rear axle and has a half circle bend.. The car will not be operated for a week or so after hose replacements.
My car has 110000 miles.
My car has a manual transmission.
Experienced mechanics share their insights in answering this question :
As long as the length is correct, and the ends on the hose match those that are being replaced, it really should not be a big deal. If the hose is installed and won’t be driven for a week anyway, this should be a sufficient alternative. If you feel you need further assistance, contact a certified mechanic, like those available at YourMechanic.com.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
Brake hoses
They transmit the hydraulic pressure to the wheel cylinders and brake callipers. Brake hoses are usually made form a special inner and outer rubber with a multi-layer fabric insert in between. There are also brake hoses that are sheathed in steel braiding (braided stainless steel brake hoses).
Heat shields and thermal barriers are simple and effective ways to protect fuel lines, wiring, brake lines and other components from the negative effects of high temperatures.
In hydraulic brake systems, brake hoses and brake lines are used to transfer brake fluid. Brake lines connect the actuation device, such as the brake master cylinder, to the hydraulic components of the wheel brake. Brake hoses are used as flexible connecting lines in all moving areas between the body and chassis.
Brake hoses are an important but often overlooked part of your car`s braking system. Their purpose is to transfer hydraulic brake fluid. This allows your brakes to function properly and safely bring your car to a stop.
The hose`s job is to carry brake fluid from a brake line fixed to the car`s body the rest of the way to the brake caliper on the wheel. Its flexibility is what allows the wheel to move with the suspension.
Hoses are used to carry fluids through air or fluid environments, and they are typically used with clamps, spigots, flanges, and nozzles to control fluid flow. Specific applications include the following: A garden hose is used to water plants in a garden or lawn, or to convey water to a sprinkler for the same purpose.
The average car has a total of four brake hoses.
Hoses are used to carry fluids through air or fluid environments, and they are typically used with clamps, spigots, flanges, and nozzles to control fluid flow. Specific applications include the following: A garden hose is used to water plants in a garden or lawn, or to convey water to a sprinkler for the same purpose.
Manufactured from either rubber or stainless steel, brake hoses are used to deliver braking force to the brake pads via hydraulic pressure and brake fluid. It is important for brake hoses to be flexible to enable the driver to steer and brake effectively, as well as manoeuvre over and around obstacles.
Fuel hose (sends gasoline from the gas tank to the engine) Radiator hose (delivers coolant to engine) Power steering hose (connects power steering pump to steering equipment) Heater hose (provides coolant to heater core)
The average car has a total of four brake hoses.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Brake hose instructions states that hose must be straightened and left in warm area before installation. How important is this.
ANSWER : As long as the length is correct, and the ends on the hose match those that are being replaced, it really should not be a big deal. If the hose is installed and won’t be driven for a week anyway, this should be a sufficient alternative. If you feel you need further assistance, contact a certified mechanic, like those available at YourMechanic.com.
When I put my foot on the brake my back left brake light goes off, when I take it off the brake the brake light comes on
ANSWER : I would suggest trying to disconnect and reconnect the wiring to the rear lights. I have seen these older Toyota vehicles rear lighting short out on the lights themselves due to the way the light circuit was made on the lamp housing. Look at the housing circuit on the light to see if one is touching another, and that could tell you why it is malfunctioning. There could also be a problem with the brake light switch. If you are not comfortable dealing with wires, I recommend getting in touch with a certified mechanic who can look at your brake light issue for you to see what’s going on.
EPC light on 2004 Jetta. Code said brake switch faulty, but brakes lights worked. Replaced brake switch, now no brake lights.
ANSWER : Hi there. The first thing that pops in my mind beyond of what you have listed is perhaps the electrical harness attached to the brake switch. Perhaps the harness itself is damaged or you have an exposed wire, loose ground wire somewhere. You might want to have a professional mobile mechanic come to your location and complete a brake lights not working inspection to help you diagnose this issue.
Low brake pedal and anti-lock brakes are not kicking in.
ANSWER : The brake pedal is working to stop the vehicle, but there may be air in the controller unit causing the ABS brakes to not function. I recommend bleeding the brake system from the farthest location from the master cylinder to the master cylinder including the ABS unit. If the brakes are still spongy after a full bleed, then the controller will need to be replaced. If you need further assistance with your brake pedal being spongy, then seek out a professional, such as one from Your Mechanic, to help you.
Supportive bar attached to brake pedal interrupts proper braking process
ANSWER : It’s possible to have someone alter the brake pedal or adapt a brake pedal from a different vehicle. You may call around to some customization shops to see if anyone is interested in taking on the project. But first, I would try reaching out to the selling dealer with your concern – especially since it is a new model. Good luck.
Brake sensor is to sensitive causing brakes to flicker while driving. 2005 Mercury Montego
ANSWER : Hi there – your brake light switch needs a minor adjustment. It is adjusted too "tight" or close to the brake pedal lever, or possibly has failed. Adjusting/replacing it will eliminate this flickering problem. I recommend a brake light isn’t working inspection performed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, and give you an accurate assessment of damage and cost estimate for repairs.
I replaced the brake light switch. Gear lever unlocked because it had locked. Now the brakes feel hard.
ANSWER : Hi, thanks for writing in. You need to check the brake switch install adjustment. You may have the switch adjusted too tight and it is holding the the brake pedal partly down. This will cause the brake master cylinder to not release the brakes when you let off the pedal. Readjust the switch away from the pedal until you feel some free play again in the pedal. This should fix the problem. If you would like help, consider having an expert automotive technician from YourMechanic come to your home or office to inspect and diagnose this issue for you, and make or suggest any repairs as needed.
Changed brake master cylinder, bled 10 times, and the pedal is soft The rear brakes are not locked but close. Truck now running rough.
ANSWER : You will have to bleed the brakes from the farthest location all the way to the master cylinder. There is still air in the lines causing the issue. Check the vibrations on the vehicle to see if the engine mounts are damaged or if the brakes are not releasing causing the engine to run harder than normal to overcome the braking force. If you need further assistance with your vehicle’s brake system, then seek out a professional, such as one from Your Mechanic, to help you.
